Description This is a 5 mW laser diode module that emits a small intense focused beam of visible red light. The module can be used with an Arduino and photoresistor...
Description The L9110 module is a two-way or dual-channel H-bridge motor controller or driver module with a small footprint. The module has two L9110 ICs, each of which can operate...
Description It's a L293d motor driver module. This motor driver module operate on 4.5v to 12v dc. It has maximum load current 600mA per motor. This module generally use for...
Description This is an L298N Motor Driver Controller Module Dual H-Bridge Motor Driver. The L298N Motor Driver Module is a dual full-bridge driver with high voltage and current. It accepts TTL logic-level...
Description This is an L293d Motor Driving Module. It is an l293d module that can drive a 4 DC Motor in one direction, or drive a 2 DC Motor in both directions....
Description This is an L293D Motor Driver Module with Voltage Protection. It can provide bidirectional drive currents of up to 600 mA at voltages from 4.5 V to 36 V....
Description This is a 2-way Remote Control Joystick and Motor Driver Hub with LAN Cable. The LAN Connector cable provides a Digital output Which Makes This Device Easy To Interface...
Description It is one of the best DIY kits for beginners who are looking to dive into embedded systems and the IoT (Internet of Things) field. This ESP32/Node MCU Shield...
Description It is one of the best DIY kits for beginners who are looking to dive into embedded systems and the IoT (Internet of Things) field. This NodeMCU Shield is...
Description This is a 4-way Remote Control Joystick and Motor Driver Hub with LAN Cable. The LAN Connector cable provides a Digital output Which Makes This Device Easy To Interface...
Description IR Proximity Sensor module uses infrared rays to detect obstacles in the range of 2-10 CM. It has 3 pins i.e., Vcc, GND and Out. Operating current of this...
Description It is one of the best DIY kits for beginners who are looking to dive into embedded systems and the IoT (Internet of Things) field. This ESP32/NodeMCU Shield is...
Description This switch module is often known as a collision, impact or limit switch. It is used to detect when a robotic vehicle collides with an object, limit switches for detecting...
Description :- It's a IIC/I2C Serial Interface Adapter Module The blue preset is to adjust the contrast of the LCD. The black jumper on the left is to enable the...
Description HW-770 V0.2 is an MP3 decoder with a Bluetooth 4.1 receiver built-in. The integrated micro USB port or a battery terminal can be used to power this board. There...
Description Suitable for a Thermoelectric cooling system where a TEC1-12706 Thermoelectric Cooler 6A Peltier Module is used. This kit includes a cooling fan and a heat sink. The larger the...
Description The HC-12 is the easiest way to transfer data over the air between two Arduino. Just connect the RX and TX pins for the transfer of data. It is...
Description The HM-06 Bluetooth module is intended for short-range wireless data communication between two microcontrollers or systems. This is the cheapest and most flexible method for wireless data transmission, and...
Description :- HC05 Bluetooth Module is used very widely as it full of features and is available at very cheap price. HC05 Module is a serial Bluetooth module with six...
Description This is a Hall Effect Sensor Module. Its range can be Adjustable with the help of 100K Multiturn Potentiometer. This sensor detects a magnetic field, which is printed as an...
Description The GPD2856A MP3 decoder IC is used on this TF card MP3 decoder board, which also includes a 2-watt L/R mixed mono audio amplifier IC (8002). This module is...
Description FS100A consists of an RF transmitter and receiver pair which operates on the frequency of 433 MHz. The receiver module requires 5V DC whereas the transmitter module can operate...
Description USB TO UART TTL 5V 3.3V FT232RL USB To Serial Adapter for Arduino is a basic module for the FTDI FT232RL USB to serial IC, Revision 2. The pinout...
Description This ESP-01 based Relay Module is suitable for wirelessly controlling appliances via WiFi. It is a single-channel relay module that can control up to 250V AC and 30V DC with...
