Description The LM2596 2A Buck Step-down Power Converter Module DC 4V~40V to 1.3V~37V utilizes an advanced microcontroller and comes with a built-in voltmeter display. LM2596 2A Buck Step-down Power Converter Module Combined...
Description The LM386 Audio Amplifier Module has a 10K adjustable resistance. It is intended for use in low-voltage consumer applications. The gain is by default set to 20 to keep...
Description : - LM393 Electret Microphone module uses LM393 as its main Op-Amp and is a single channel signal output sensor module. LM393 module has 3 pins which are Out,...
Description :- The rotary encoder is used to detect axial movement and its direction. Rotary Encoder is an incremental electro-mechanical device that converts the angular position or motion of a...
Description This is an LDR Light Sensor Module with Special Day/Night Invert Logic. Light Dependent Resistor is a special type of resistor used for the detection of light. As it...
Description This is an LDR Light Sensor Module. Light Dependent Resistor is a special type of resistor used for the detection of light. As it is a type of resistor...
Description This is a 5 mW laser diode module that emits a small intense focused beam of visible red light. The module can be used with an Arduino and photoresistor...
Description The L9110 module is a two-way or dual-channel H-bridge motor controller or driver module with a small footprint. The module has two L9110 ICs, each of which can operate...
Description It's a L293d motor driver module. This motor driver module operate on 4.5v to 12v dc. It has maximum load current 600mA per motor. This module generally use for...
Description This is an L298N Motor Driver Controller Module Dual H-Bridge Motor Driver. The L298N Motor Driver Module is a dual full-bridge driver with high voltage and current. It accepts TTL logic-level...
Description :- It's a L298 2A dual motor driver module with PWM controller. This is a High power motor driver perfect for driving DC motor and stepper motor. It can Can...
Description This is an L293d Motor Driving Module. It is an l293d module that can drive a 4 DC Motor in one direction, or drive a 2 DC Motor in both directions....
Description This is an L293D Motor Driver Module with Voltage Protection. It can provide bidirectional drive currents of up to 600 mA at voltages from 4.5 V to 36 V....
Description This is a 2-way Remote Control Joystick and Motor Driver Hub with LAN Cable. The LAN Connector cable provides a Digital output Which Makes This Device Easy To Interface...
Description It is one of the best DIY kits for beginners who are looking to dive into embedded systems and the IoT (Internet of Things) field. This ESP32/Node MCU Shield...
Description It is one of the best DIY kits for beginners who are looking to dive into embedded systems and the IoT (Internet of Things) field. This NodeMCU Shield is...
Description This is a 4-way Remote Control Joystick and Motor Driver Hub with LAN Cable. The LAN Connector cable provides a Digital output Which Makes This Device Easy To Interface...
Description IR Proximity Sensor module uses infrared rays to detect obstacles in the range of 2-10 CM. It has 3 pins i.e., Vcc, GND and Out. Operating current of this...
Description It is one of the best DIY kits for beginners who are looking to dive into embedded systems and the IoT (Internet of Things) field. This ESP32/NodeMCU Shield is...
Description This switch module is often known as a collision, impact or limit switch. It is used to detect when a robotic vehicle collides with an object, limit switches for detecting...
Description :- It's a IIC/I2C Serial Interface Adapter Module The blue preset is to adjust the contrast of the LCD. The black jumper on the left is to enable the...
Description HW-770 V0.2 is an MP3 decoder with a Bluetooth 4.1 receiver built-in. The integrated micro USB port or a battery terminal can be used to power this board. There...
Description Suitable for a Thermoelectric cooling system where a TEC1-12706 Thermoelectric Cooler 6A Peltier Module is used. This kit includes a cooling fan and a heat sink. The larger the...
Description The HC-12 is the easiest way to transfer data over the air between two Arduino. Just connect the RX and TX pins for the transfer of data. It is...
